Smart serial cable nut serial numbers#
Smart serial cable nut serial number#
Smart serial cable nut full#
Smart serial cable nut pro#
Smart serial cable nut code#

Also, it comes with a very handy GUI and the fact that it is based on FreeBSD makes it even greater. It can turn any old machine into a very powerful firewall/router in 10 minutes or less. You can query the UPS when it is operating in the on-line, bypass, or on-battery modes of operation.One of my favorite Open Source appliances is pfSense. The UPS's estimated remaining run time in minutes. Whether power is being provided by the external utility (power company) Only shown when the UPS reports this status

Smart serial cable nut full#

The typical accuracy of this measurement is в‘% of the full scale value of 63 Hz When operating on-line, the UPS's internal operating frequency is synchronized to the line within variations of 3 Hz of the nominal 50 or 60 Hz. The typical accuracy of this measurement is В±5% of the maximum value (depending on the UPS's nominal battery voltage) The UPS's remaining battery capacity as a percent of the fully charged condition Note: The test begins only if the battery capacity is 100%.

Smart serial cable nut code#

The country code may be one of the following: UPS version, consists of three fields: SKU number, firmware revision, country code.

Smart serial cable nut serial numbers#

Newer SmartUPS models have 12-character serial numbers

Smart serial cable nut serial number#

UPS's nominal battery voltage rating (this is not the UPS's actual battery voltage)ДЄ string of at least 8 characters directly representing the UPS's serial number as set at the factory. Less than 32 ASCII character string consisting of the UPS model name (the words on the front of the UPS itself) UPS's date of manufacture in the format 'mm/dd/yy' (month, day, year). The typical accuracy of this measurement is в“% of the maximum of 105% The UPS's output load as a percentage of full rated load in Watts. In this case, the router will wait until the UPS reports that the battery power is below 10%

0s - the router will go into hibernate mode according to the min-runtime setting.

The router waits that amount of time and then goes into hibernate mode until the UPS reports that the 'utility' power is back

0s - the router will continue to work as long as the battery is supplying sufficient voltage.

never - the router will go to hibernate mode when the 'battery low' signal is sent indicating that the battery power is below 10%.

When the value reaches the min-runtime value, the router will go to hibernate mode. After a 'utility' failure, the router will monitor the runtime-left value. (Applies to RouterOS version 6, implemented since v6.17) Disabling it can fix compatibility issues with some UPS models.

Whether to check UPS capabilities before reading information. low-battery - alarm only when the battery is lowД¬heck-capabilities ( yes | no Default: yes).immediate - alarm immediately after the on-battery event.delayed - alarm is delayed to the on-battery event.Select key which will enter setup on boot:ДЄlarm-setting ( delayed | immediate | low-battery | none Default: immediate) This can be done in the RouterBOOT options during boot time or via the RouterBoard Settings in WinboxВ : This is to avoid accidental opening of the setup menu if the UPS unit sends some data to the serial port during RouterBOARD startup. If using a RouterBOARD device, make sure to set your 'RouterBOOT setup key' to Delete instead of the default Any key. If no cable came with the UPS, a cable may be ordered from APC or one can be made 'in-house'.

Smart serial cable nut pro#

The serial APC UPS (BackUPS Pro or SmartUPS) requires a special serial cable (unless connected with USB).

monitoring of all 'smart' mode status information supported by UPS.

UPS battery test and run time calibration test.

hibernate and safe reboot on power and battery failure.

The UPS monitor feature on the MikroTik RouterOS supports If the UPS battery is drained and the router loses all power, the router will power back to full operation when the вЂutilityвЂ™ power returns. The router will then continue to monitor the UPS (while in hibernate mode) and then restart itself when the utility power returns. To do this, the router will monitor the UPS and set itself to hibernate mode when the utility power is down and the UPS battery has less than 10% of its battery power left. The basic purpose of this feature is to ensure that the router will come back online after an extended power failure. This feature enables the network administrator to monitor the UPS and set the router to вЂgracefullyвЂ™ handle any power outage with no corruption or damage to the router. The UPS monitor service is not included in the default set of packages so it needs to be downloaded and installed manually with ups.npk package. The UPS monitor feature works with APC UPS units that support вЂњsmartвЂќ signalling over serial RS232 or USB connection.